Jewellery box with lid mockup and dieline

The flat dieline

Jewellery box with lid: what to know

Jewellery boxes are small rigid lid-and-base boxes for rings, earrings and bangles. They are opened in front of the person receiving them, so the feel of the box matters as much as the print.

• Plan the insert first: a slotted foam or velvet insert for rings, a flat pad for earrings, a deeper cavity for bangles.
• Bangles need a box sized to their diameter, often much larger than a ring box.
• A foil logo on a plain coloured wrap is a common, understated premium look.
• If the box is couriered, plan an outer mailer as well. Rigid boxes scuff in transit.

Parts of a rigid lid-and-base box

A lid-and-base box is two separate trays: a base that holds the product and a lid that slides down over it. It is the classic gift box: the lid lifts straight off, so opening it feels like an occasion, and the walls are stiff enough to stack. Premium versions are rigid (thick greyboard wrapped in printed paper); everyday versions fold up from a single sheet of paperboard.

Base tray

Floor and four walls that hold the product. Its inside size is the size you design to.

Lid

A slightly larger tray that fits over the base. A shallow lid covers the top edge; a full-depth lid reaches the bottom.

Turn-ins

On rigid boxes, the wrap paper folds over the top edge and into the walls, so no raw board shows.

Wrap

The printed paper glued around a rigid box. This is where your artwork goes.

Insert (optional)

A card or foam tray inside that holds each item in place, and a ribbon to lift it out.

How to size it

1. Measure the product (or the product in its inner pack) at its widest points: length, width, height.
2. Add 2 to 3 mm on each side for a snug fit, more if there is an insert or tissue paper.
3. Enter those as Inside sizes in the studio. The outside size, which grows by the board thickness and the lid, is shown under the fields.
4. Pick the lid depth: a shallow lid (about a third of the box height) is cheaper and easier to open; a full-depth lid looks more premium.

Materials and finishes

Greyboard (chipboard) 1.5 to 3 mm, wrapped in printed paper

Rigid gift boxes: jewellery, perfume, premium sweets, hampers. Strong and heavy, delivered already made up.

White paperboard, 300 to 400 gsm

Folding lid-and-base boxes: lighter, ships flat, lower cost. Good for everyday gifts and sweets.

Kraft paperboard

A natural, unbleached look; prints darker and less vivid than white board.

Finishes

Matte or gloss lamination

Protects the print from scuffs and fingerprints.

Soft-touch lamination

A velvety feel for premium boxes; shows fingerprints less than gloss.

Foil stamping and embossing

Gold or silver logos and raised lettering. Keep foil details larger than about 0.3 mm so they stay crisp.

Mistakes to avoid

• Designing to the outside size: the product then does not fit. Design to the inside and let the walls grow outward.
• Forgetting the lid sits over the base: on rigid boxes the lid is a few millimetres larger all round.
• Placing text right at the lid edge, where it folds over the turn-in and gets cut or distorted. Keep 5 mm clear of every edge.
• Low-resolution images: artwork needs about 300 dpi at the printed size. A web logo is usually too small.

How to make it in the studio

1. Open it. Press Customise this jewellery box with lid. It opens in the 3D studio at 90 x 90 x 40 mm.
2. Set the size. In the Size panel, choose whether you are entering the Inside or Outside size, then type your measurements. The other one is shown underneath.
3. Add your design. In the Design panel, upload your logo or artwork: it goes on the top first. Pick other faces to add colours, text or images to each.
4. Check it in 3D. Turn the pack around, and use the Flat to Closed slider to watch it fold. Switch to the Dieline view to see the artwork on the dieline.
5. Download. The Download panel gives you the PDF dieline to send your printer first, then mockup images for your store or social posts.
6. Get it made. If you want a quote, send the design to packitmama from the Download panel, and we will reply personally.

Questions